• 注册
  • 综合讨论 综合讨论 关注:22 内容:75

    Klipper配置远程+近程双挤出机

  • 查看作者
  • 打赏作者
    • 1
    • 综合讨论
      • 两个挤出机,一个再近程,一个再远程

      • 此办法可以混合实用挤出机,比如近程bmg远程M4

      • 我想要这么搞的原因是,这样对近程挤出机要求很低,提供一点压力,就可以非常顺的打印。 远程会释放近程挤出机的压力

      • 此方式需要调整挤出机压紧轮的压力,因为压力会影响到挤出机的挤出长度,除非用供料管,不然两个挤出机之间的长度会有变化

      ##  In E0-MOT Position[extruder]step_pin: PD5
      dir_pin: PD6
      enable_pin: !PD4##  Update value below when you perform extruder calibration##  If you ask for 100mm of filament, but in reality it is 98mm:##  rotation_distance = <previous_rotation_distance> * <actual_extrude_distance> / 100##  22.6789511 is a good starting pointrotation_distance: 25.12    #bmg ##  Update Gear Ratio depending on your Extruder Type##  Use 50:17 for Afterburner/Clockwork (BMG Gear Ratio)##  Use 80:20 for M4, M3.1gear_ratio: 50:17               #BMG Gear Ratiomicrosteps: 32full_steps_per_rotation: 200    #200 for 1.8 degree, 400 for 0.9 degreenozzle_diameter: 0.400filament_diameter: 1.75##      In E0 OUT Positionheater_pin: PB15##  Validate the following ATC Semitec 104GT-2 thermistor type to make sure it is correct#sensor_type: ATC Semitec 104GT-2sensor_type: PT1000
      sensor_pin: PC0
      pullup_resistor: 4700min_temp: 10max_temp: 270max_power: 1.0min_extrude_temp: 170control = pid
      pid_kp = 26.213pid_ki = 1.304pid_kd = 131.721##  Try to keep pressure_advance below 1.0pressure_advance: 0.05##  Default is 0.040, leave stockpressure_advance_smooth_time: 0.040##  In E0-MOT Position##  Make sure to update below for your relevant driver (2208 or 2209)[tmc2209 extruder]uart_pin: PD7interpolate: falserun_current: 0.6hold_current: 0.6sense_resistor: 0.110stealthchop_threshold: 0##重点在下面##  In E4-MOT Position[extruder_stepper my_extra_stepper]extruder = extruder  #同步到extruder上step_pin: PE1
      dir_pin: PE0
      enable_pin: !PC5
      microsteps:32rotation_distance: 25.12    #bmg gear_ratio: 50:17               #BMG Gear Ratiofull_steps_per_rotation: 200    #200 for 1.8 degree, 400 for 0.9 degree#shared_heater: extruder#nozzle_diameter: 0.400#filament_diameter: 1.75##  In E4-MOT Position##  Make sure to update below for your relevant driver (2208 or 2209)[tmc2209 extruder_stepper my_extra_stepper]uart_pin: PD11interpolate: falserun_current: 0.6hold_current: 0.6sense_resistor: 0.110stealthchop_threshold: 0

      打印菜鸟
      ##  In E0-MOT Position[extruder]
      step_pin: PD5
      dir_pin: PD6
      enable_pin: !PD4
      ##  Update value below when you perform extruder calibration
      ##  If you ask for 100mm of filament, but in reality it is 98mm:
      ##  rotation_distance = <previous_rotation_distance> * <actual_extrude_distance> / 100
      ##  22.6789511 is a good starting pointrotation_distance: 25.12    #bmg 
      ##  Update Gear Ratio depending on your Extruder Type
      ##  Use 50:17 for Afterburner/Clockwork (BMG Gear Ratio)
      ##  Use 80:20 for M4, M3.1gear_ratio: 50:17              
      #	BMG Gear Ratiomicrosteps: 32full_steps_per_rotation: 200    
      #	200 for 1.8 degree, 400 for 0.9 degreenozzle_diameter: 0.400filament_diameter: 1.75
      ##  In E0 OUT Positionheater_pin: PB15
      ##  Validate the following ATC Semitec 104GT-2 thermistor type to make sure it is correct#sensor_type: ATC Semitec 104GT-2sensor_type: PT1000
      
      sensor_pin: PC0
      pullup_resistor: 4700min_temp: 10max_temp: 270max_power: 1.0min_extrude_temp: 170control = pid
      pid_kp = 26.213pid_ki = 1.304pid_kd = 131.721
      ##  Try to keep pressure_advance below 1.0pressure_advance: 0.05
      ##  Default is 0.040, leave stockpressure_advance_smooth_time: 0.040
      ##  In E0-MOT Position
      ##  Make sure to update below for your relevant driver (2208 or 2209)
      [tmc2209 extruder]
      uart_pin: PD7
      interpolate: falserun_current: 0.6
      hold_current: 0.6
      sense_resistor: 0.110
      stealthchop_threshold: 0
      
      ##重点在下面##  
      
      In E4-MOT Position[extruder_stepper my_extra_stepper]extruder = extruder  #同步到extruder上step_pin: PE1
      dir_pin: PE0
      enable_pin: !PC5
      microsteps:32rotation_distance: 25.12    
      #bmg gear_ratio: 50:17               
      #BMG Gear Ratiofull_steps_per_rotation: 200    
      #200 for 1.8 degree, 400 for 0.9 degree#shared_heater: extruder#nozzle_diameter: 0.400
      #filament_diameter: 1.75
      ##  In E4-MOT Position
      ##  Make sure to update below for your relevant driver (2208 or 2209)
      [tmc2209 extruder_stepper my_extra_stepper]
      uart_pin: PD11
      interpolate: falserun_current: 0.6
      hold_current: 0.6
      sense_resistor: 0.110
      stealthchop_threshold: 0

      这个段点对不。。

      回复

      请登录之后再进行评论

      登录
      帖子间隔 侧栏位置: