• 注册
  • 综合讨论 综合讨论 关注:22 内容:75

    SKR V1.4Turbo V1.8 配置文件klipper

  • 查看作者
  • 打赏作者
    • 综合讨论
    • 简介:

      • 双Z配置,可用于blv等常见双z,corexy结构机型,都是一样的。

      • 只配置了挤出功能,所以需要手动调平,可以快速开始打印,其他的慢慢玩

      • xyz正常位置,第二个z放在E1电机位置,挤出机位置不变

      • 使用了无位置传感器归零,所以不需要接xy位置的限位开关

      • Fan0用于e3d v6散热

      • TB为热床

      • TH0为e3d v6

      • USB连接树莓派,刷程序的时候需要选择使用smoothie 的bootloader

      • 其它想不到什么需要说的,大伙可以回复跟新

      Code# This file contains common pin mappings for the BIGTREETECH SKR V1.4# board. To use this config, the firmware should be compiled for the# LPC1768 or LPC1769(Turbo).# See docs/Config_Reference.md for a description of parameters.#fysetc cheetah V2[mcu]# serial = /dev/serial/by-id/usb-Klipper_lpc1769_LPC1769-1-if00serial = /dev/serial/by-id/usb-Klipper_lpc1769_xqz15-if00#skr mini#[mcu E0]#serial = /dev/serial/by-id/usb-Klipper_stm32f103xe_xiaoqianzi103-if00[stepper_x]step_pin: P2.2dir_pin: P2.6enable_pin: !P2.1microsteps: 32rotation_distance: 40full_steps_per_rotation: 200# endstop_pin: PB14endstop_pin: tmc2209_stepper_x: virtual_endstop
      position_endstop: 0position_max: 220homing_speed: 50[tmc2209 stepper_x]uart_pin: P1.10run_current: 1.200hold_current: 0.500stealthchop_threshold: 0interpolate: Truedriver_sgthrs: 45diag_pin: P1.29[stepper_y]step_pin: P0.19dir_pin: P0.20enable_pin: !P2.8microsteps: 32rotation_distance: 40full_steps_per_rotation: 200# endstop_pin: PB13endstop_pin: tmc2209_stepper_y: virtual_endstop
      position_endstop: 0position_max: 220homing_speed: 50[tmc2209 stepper_y]uart_pin: P1.9run_current: 1.200hold_current: 0.500stealthchop_threshold: 0interpolate: Truedriver_sgthrs: 45diag_pin: P1.28[stepper_z]step_pin: P0.22dir_pin: P2.11enable_pin: !P0.21microsteps: 32rotation_distance: 8full_steps_per_rotation: 200endstop_pin: ^P1.27#endstop_pin: !PA0position_endstop: 0position_max: 220homing_speed: 15[tmc2209 stepper_z]uart_pin: P1.8#tx_pin: PA2#uart_address: 1run_current: 0.800hold_current: 0.600stealthchop_threshold: 0[stepper_z1]step_pin: P1.15dir_pin: P1.14enable_pin: !P1.16microsteps: 32rotation_distance: 8#endstop_pin: !P0.18#position_endstop: 0.0#position_max: 300[tmc2209 stepper_z1]uart_pin: P1.1run_current: 0.80hold_current: 0.60stealthchop_threshold: 0[extruder]step_pin: P2.13dir_pin: !P0.11enable_pin: !P2.12microsteps: 16rotation_distance: 33.500nozzle_diameter: 0.400filament_diameter: 1.750heater_pin: P2.7sensor_type: EPCOS 100K B57560G104F
      sensor_pin: P0.24control: pid
      pid_Kp: 21.527pid_Ki: 1.063pid_Kd: 108.982min_temp: 0max_temp: 250[tmc2209 extruder]uart_pin: P1.4run_current: 0.650hold_current: 0.500stealthchop_threshold: 5[heater_bed]heater_pin: P2.5sensor_type: ATC Semitec 104GT-2sensor_pin: P0.25control: pid
      pid_Kp: 54.027pid_Ki: 0.770pid_Kd: 948.182min_temp: 0max_temp: 130[heater_fan nozzle_cooling_fan]pin: P2.3heater: extruder
      heater_temp: 38.0fan_speed: 1.0[printer]kinematics: corexy
      max_velocity: 300max_accel: 10000max_z_velocity: 50max_z_accel: 1000#[temperature_sensor mcu_temp]#sensor_type: temperature_mcu#min_temp: 0#max_temp: 100#[temperature_sensor raspberry_pi]#sensor_type: temperature_host#min_temp: 10#max_temp: 100[virtual_sdcard]path: ~/gcode_files
      
      [display_status]
      
      [pause_resume]
      
      [gcode_macro PAUSE]
      rename_existing: BASE_PAUSE
      default_parameter_X: 260    # edit to your preferred park position
      default_parameter_Y: 260    # edit to your preferred park position
      default_parameter_Z: 10     # edit to your preferred park position
      default_parameter_E: 1      # edit to your preferred retract length
      gcode:
          SAVE_GCODE_STATE NAME=PAUSE_state
          BASE_PAUSE
          G91
          G1 E-{E} F2100
          G1 Z{Z}
          G90
          G1 X{X} Y{Y} F6000
      
      [gcode_macro RESUME]
      rename_existing: BASE_RESUME
      default_parameter_E: 1      # edit to your preferred retract length
      gcode:
          G91
          G1 E{E} F2100
          G90
          RESTORE_GCODE_STATE NAME=PAUSE_state MOVE=1
          BASE_RESUME
      
      [gcode_macro CANCEL_PRINT]
      rename_existing: BASE_CANCEL_PRINT
      gcode:
          TURN_OFF_HEATERS
          CLEAR_PAUSE
          SDCARD_RESET_FILE
          BASE_CANCEL_PRINT
      
      [gcode_macro PRINT_START]
      #   Use PRINT_START for the slicer starting script - PLEASE CUSTOMISE THE SCRIPT
      gcode:
          G28
      
      [gcode_macro PRINT_END]
      #   Use PRINT_START for the slicer starting script - PLEASE CUSTOMISE THE SCRIPT
      gcode:
          G28 x, y 
      
      #[adxl345]
      #cs_pin: rpi:None
      
      #[resonance_tester]
      #accel_chip: adxl345
      #probe_points: 100,100,20
      
      [printer]
      max_accel: 10000
      max_accel_to_decel: 10000
      
      ########################################
      # TMC2208 configuration
      ########################################
      
      #[tmc2208 stepper_x]
      #uart_pin: P1.10
      #run_current: 0.800
      #hold_current: 0.500
      #stealthchop_threshold: 250
      #
      #[tmc2208 stepper_y]
      #uart_pin: P1.9
      #run_current: 0.800
      #hold_current: 0.500
      #stealthchop_threshold: 250
      #
      #[tmc2208 stepper_z]
      #uart_pin: P1.8
      #run_current: 0.650
      #hold_current: 0.450
      #stealthchop_threshold: 30
      #
      #[tmc2208 extruder]
      #uart_pin: P1.4
      #run_current: 0.800
      #hold_current: 0.500
      #stealthchop_threshold: 5
      #
      #[tmc2208 extruder1]
      #uart_pin: P1.1
      #run_current: 0.800
      #hold_current: 0.500
      #stealthchop_threshold: 5
      
      ########################################
      # TMC2130 configuration
      ########################################
      
      #[tmc2130 stepper_x]
      #cs_pin: P1.10
      #spi_software_miso_pin: P0.5
      #spi_software_mosi_pin: P1.17
      #spi_software_sclk_pin: P0.4
      #run_current: 0.800
      #hold_current: 0.500
      #stealthchop_threshold: 250
      #diag1_pin: P1.29
      
      #[tmc2130 stepper_y]
      #cs_pin: P1.9
      #spi_software_miso_pin: P0.5
      #spi_software_mosi_pin: P1.17
      #spi_software_sclk_pin: P0.4
      #run_current: 0.800
      #hold_current: 0.500
      #stealthchop_threshold: 250
      #diag1_pin: P1.28
      
      #[tmc2130 stepper_z]
      #cs_pin: P1.8
      #spi_software_miso_pin: P0.5
      #spi_software_mosi_pin: P1.17
      #spi_software_sclk_pin: P0.4
      #run_current: 0.650
      #hold_current: 0.450
      #stealthchop_threshold: 30
      #diag1_pin: P1.27
      
      #[tmc2130 extruder]
      #cs_pin: P1.4
      #spi_software_miso_pin: P0.5
      #spi_software_mosi_pin: P1.17
      #spi_software_sclk_pin: P0.4
      #run_current: 0.800
      #hold_current: 0.500
      #stealthchop_threshold: 5
      #diag1_pin: P1.26
      
      #[tmc2130 extruder1]
      #cs_pin: P1.1
      #spi_software_miso_pin: P0.5
      #spi_software_mosi_pin: P1.17
      #spi_software_sclk_pin: P0.4
      #run_current: 0.800
      #hold_current: 0.500
      #stealthchop_threshold: 5
      #diag1_pin: P1.25
      
      ########################################
      # EXP1 / EXP2 (display) pins######################################### See the sample-lcd.cfg file for definitions of common LCD displays.#*# <---------------------- SAVE_CONFIG ---------------------->#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.#*##*# [input_shaper]#*# shaper_type_x = zv#*# shaper_freq_x = 102.4#*# shaper_type_y = 2hump_ei#*# shaper_freq_y = 74.0

      请登录之后再进行评论

      登录
      帖子间隔 侧栏位置: